The M18 size of Hex Bolt is dimensioned by GB/T 5783 / ISO 4017. The tables below give the dimensional row from the standard, the drill and spanner sizes that go with it, and the assembly torque per property class. The technical drawing on this page redraws to the exact values selected.
M18 Dimensional Row (GB/T 5783 / ISO 4017)
| Size | Pitch (mm) | Nominal diameter d (mm) | Length L (mm) | Width across flats s (mm) | Width across corners e (mm) | Head height k (mm) |
|---|---|---|---|---|---|---|
| M18 | 2.5 | 18 | 100 | 27.0 | 30.14 | 11.5 |
Spanner & Drive for M18 Hex Bolt — GB/T 5783 / ISO 4017 (Series 010)
M18 Hex Bolt — GB/T 5783 / ISO 4017 (Series 010) have a width across flats of 27.0 mm — fit a 27.0 mm open-ended spanner or socket. Prefer a 6-point socket over a 12-point: it loads the corners of the 27.0 mm hex far less, which matters on plated heads and on anything that will be re-used. Set preload with a torque wrench rather than by arm.
Hole Sizes for M18
| Coarse-thread pitch (ISO 724) | 2.5 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 20 mm |
| Tapping drill, coarse thread | 15.5 mm |
Tightening Torque for M18
| Class 8.8 (dry, ~µ 0.125) | ≈ 297 Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ 423 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 495 Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M18
| Tensile stress area As (ISO 724) | 192 mm² |
|---|---|
| Proof load, class 8.8 | 115 kN |
| Proof load, class 10.9 | 160 kN |
| Proof load, class 12.9 | 187 kN |
| Min. ultimate tensile load, class 8.8 | 160 kN |
Proof load = tensile stress area × the proof stress Sp of the class, per ISO 898-1 — Sp is a lower figure than the yield stress Rp0.2 and the two are not interchangeable. The stress area is computed from this size's own diameter and pitch, so a fine-pitch designation gives the fine-pitch figure. Design the joint so the working preload stays below the proof load of the class selected.
M18 Hex Bolt — GB/T 5783 / ISO 4017 (Series 010) Weight
A steel M18 hex bolt at the listed 100 mm length weighs approximately 257 g each — about 257 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³).
Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Installation Tips for M18 Hex Bolt — GB/T 5783 / ISO 4017 (Series 010)
- Use a 6-point socket where access allows — 12-point sockets are more prone to rounding the corners on smaller sizes.
- A flanged head is its own washer. Adding a flat one under it lifts the serrations clear of the surface they are meant to bite, which is the whole locking mechanism gone.
- At M18 the stretch in the bolt becomes the controlling factor — for critical joints, use angle-controlled or stretch-controlled tightening instead of pure torque.
Mating Parts for M18
For M18, pair with a M18 hex nut (ISO 4032 / DIN 934) and, where used, a M18 flat washer (ISO 7089 / DIN 125A) under the head and under the nut.
Custom manufacturing · Made to drawing
Need hex bolt in a size this table does not list?
This page covers M18 hex bolt. Lengths and thread lengths outside the standard table are the commonest request, followed by a drive the standard does not offer and a head marked with your own part number. Made by cold heading or hot forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
