The M6 size of Clamping Handle Screw (Long) is dimensioned by DIN 6336 / GN 313. The tables below give the dimensional row from the standard, the drill and spanner sizes that go with it, and the assembly torque per property class. The technical drawing on this page redraws to the exact values selected.
M6 Dimensional Row (DIN 6336 / GN 313)
| Thread size | Pitch (mm) | Length L (mm) | Handle length (mm) | Knob diameter (mm) | Reference standard |
|---|---|---|---|---|---|
| M6 | 1.0 | 25 | 50 | 32 | DIN 6336 / GN 313 |
Spanner & Drive for M6 Clamping Handle Screw (Long) — DIN 6336 / GN 313 (Series 044)
Drive geometry for M6 Clamping Handle Screw (Long) — DIN 6336 / GN 313 (Series 044) is given by the row above; match the tool to the listed values.
Hole Sizes for M6
| Coarse-thread pitch (ISO 724) | 1 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 6.6 mm |
| Tapping drill, coarse thread | 5 mm |
Tightening Torque for M6
| Class 8.8 (dry, ~µ 0.125) | ≈ 10 Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ 14 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 17 Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M6
| Tensile stress area As (ISO 898-1) | 20.1 mm² |
|---|---|
| Proof load, class 8.8 | 12 kN |
| Proof load, class 10.9 | 17 kN |
| Proof load, class 12.9 | 19 kN |
| Min. ultimate tensile, class 8.8 | 16 kN |
Proof load = stress area × proof stress per ISO 898-1. Design joints so the working preload stays below the proof load of the selected class.
M6 Clamping Handle Screw (Long) — DIN 6336 / GN 313 (Series 044) Weight
A steel M6 clamping handle screw (long) at the listed 25 mm length weighs approximately 5.5 g each — about 5.5 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³). Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Common Applications for M6 Clamping Handle Screw (Long) — DIN 6336 / GN 313 (Series 044)
M6 Clamping Handle Screw (Long) — DIN 6336 / GN 313 (Series 044) are commonly specified for general-purpose machinery, jigs, fixturing and light structural connections.
Mating Parts for M6
For M6, pair with a M6 hex nut (ISO 4032 / DIN 934) and, where used, a M6 flat washer (ISO 7089 / DIN 125A) under the head and under the nut.
When to Step Up or Down from M6
When the joint preload approaches the proof load of M6 class 8.8, step up to M8 class 8.8 (or move to M6 class 10.9). When the joint is over-specified, M5 often saves weight and cost without losing the safety margin.