This page covers M8 Phillips Countersunk Machine Screw to GB/T 819.1 / ISO 7046: the full dimensional row, hole and tool sizes, proof-load data and typical applications. All values are taken from the governing standards (GB/T 819.1 / ISO 7046 together with ISO 273, ISO 724 and ISO 898-1 where applicable).
M8 Dimensional Row (GB/T 819.1 / ISO 7046)
| Size | Pitch (mm) | Length L (mm) | Head diameter dk (mm) | Head height k (mm) | Cross recess | Countersink angle (deg) | Reference standard |
|---|---|---|---|---|---|---|---|
| M8 | 1.25 | 50 | 14.5 | 4.0 | PH3 | 90 | ISO 7046 / GB/T 819 |
Spanner & Drive for M8 Phillips Countersunk Machine Screw — GB/T 819.1 / ISO 7046 (Series 029)
The hex socket for M8 Phillips Countersunk Machine Screw — GB/T 819.1 / ISO 7046 (Series 029) is shown in the spec table — use the matching Allen / hex key (an ISO 2936 hex key set covers the full range). A T-handle Allen key gives the best feel for setting preload by feel; for production work use a torque-controlled driver.
Hole Sizes for M8
| Coarse-thread pitch (ISO 724) | 1.25 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 9 mm |
| Tapping drill, coarse thread | 6.8 mm |
Tightening Torque for M8
| Class 8.8 (dry, ~µ 0.125) | ≈ 25 Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ 35 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 41 Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M8
| Tensile stress area As (ISO 898-1) | 36.6 mm² |
|---|---|
| Proof load, class 8.8 | 21 kN |
| Proof load, class 10.9 | 30 kN |
| Proof load, class 12.9 | 36 kN |
| Min. ultimate tensile, class 8.8 | 29 kN |
Proof load = stress area × proof stress per ISO 898-1. Design joints so the working preload stays below the proof load of the selected class.
M8 Phillips Countersunk Machine Screw — GB/T 819.1 / ISO 7046 (Series 029) Weight
A steel M8 phillips countersunk machine screw at the listed 50 mm length weighs approximately 65 g each — about 65 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³). Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Common Applications for M8 Phillips Countersunk Machine Screw — GB/T 819.1 / ISO 7046 (Series 029)
M8 Phillips Countersunk Machine Screw — GB/T 819.1 / ISO 7046 (Series 029) are commonly specified for machine assembly, general engineering, plant maintenance and OEM equipment.
Installation Tips for M8 Phillips Countersunk Machine Screw — GB/T 819.1 / ISO 7046 (Series 029)
- Use a quality Allen key fully seated in the socket — partial engagement is the most common cause of stripped sockets at this size.
- For countersunk and button-head variants, chamfer the through-hole to seat the head flush without preloading the head/shank fillet.
Mating Parts for M8
For M8, pair with a M8 hex nut (ISO 4032 / DIN 934) and, where used, a M8 flat washer (ISO 7089 / DIN 125A) under the head and under the nut.