Skip to content
info@engineeringhardware.com
Request a Quote

Bearings & Bushings · ISO / DIN

ISO Rod End Bearing — ISO / DIN (Series 107)

ISO is the international standard for rod end bearing — iso / din (series 107). This page sets out what the standard governs, the size range it specifies, and the related standards you will see referenced in datasheets.

ISO — Scope

ISO specifies the dimensions and tolerances of rod end bearing — iso / din (series 107). Material, property class, surface finish and packaging are governed by separate documents in the same standards family (for example ISO 898-1 for the mechanical property classes of bolts and screws).

Tolerance & Product Grades

ISO, alongside the related ISO / DIN entries on this site, specifies product grades (typically A or B for fine work and C for general engineering) and tolerance classes for the controlling dimensions. Choose the grade against the precision your application requires.

Dimensions Specified by ISO

Bore d (mm)Thread sizePitch (mm)Total length (mm)Hex width (mm)Static load Cor (kN)Reference standard
5M50.84082.2DIN ISO 12240 / GB/T 9163
6M61.046103.0DIN ISO 12240 / GB/T 9163
8M81.2557125.0DIN ISO 12240 / GB/T 9163
10M101.571148.0DIN ISO 12240 / GB/T 9163
12M121.75841712.0DIN ISO 12240 / GB/T 9163
16M162.01052221.0DIN ISO 12240 / GB/T 9163
20M202.51312733.0DIN ISO 12240 / GB/T 9163
25M243.01603252.0DIN ISO 12240 / GB/T 9163

Companion Standards

ISO controls only the geometry of rod end bearing — iso / din (series 107). The mechanical strength is set by ISO 898-1 (bolts and screws) or ISO 898-2 (nuts); the surface finish is governed by separate finish standards (e.g. ISO 4042 for electroplating). For corrosion testing, the relevant document is ISO 9227 (neutral salt spray).

When to Specify ISO

Choose ISO for international engineering work and OEM supply where ISO standards are the contractual reference. It is the default modern specification for rod end bearing — iso / din (series 107).

Technical Drawing

Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.

Sends the selected values to the quote form below.

Request a Quote

Adjust the parameters in the drawing above and click "Request this configuration" to send the exact specification straight to this form.

Request a Quotation

Specification
Business Information

Dimensions & Specifications (ISO / DIN)

Bore d (mm)Thread sizePitch (mm)Total length (mm)Hex width (mm)Static load Cor (kN)Reference standard
5M50.84082.2DIN ISO 12240 / GB/T 9163
6M61.046103.0DIN ISO 12240 / GB/T 9163
8M81.2557125.0DIN ISO 12240 / GB/T 9163
10M101.571148.0DIN ISO 12240 / GB/T 9163
12M121.75841712.0DIN ISO 12240 / GB/T 9163
16M162.01052221.0DIN ISO 12240 / GB/T 9163
20M202.51312733.0DIN ISO 12240 / GB/T 9163
25M243.01603252.0DIN ISO 12240 / GB/T 9163

Frequently Asked Questions

When did ISO last revise its dimensional table?

ISO standards for rod end bearing — iso / din (series 107) are reviewed on roughly a five-year cycle. Always reference the latest published edition (or the edition cited contractually); the dimensional table on this page reflects the current commercially-supplied form.

What does ISO specify for Rod End Bearing — ISO / DIN (Series 107)?

ISO specifies the dimensions and tolerances of rod end bearing — iso / din (series 107). Material and property class are governed by separate standards in the same family.

What product grades does ISO define?

ISO typically distinguishes product grades for precision (A/B) and general engineering (C). The selection for Rod End Bearing — ISO / DIN (Series 107) depends on the precision your application requires.

Does ISO specify the mechanical strength?

No. ISO controls only the geometry of rod end bearing — iso / din (series 107). The mechanical strength is set by ISO 898-1 (bolts / screws) or ISO 898-2 (nuts), and the finish is governed by separate standards.

How do I request a quotation?

Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.