T 5783 covers the dimensional requirements for hex bolt, fully threaded. Reproduced below: the complete size table, the tolerance grades, and the companion and equivalent standards referenced when ordering to this document.
T 5783 — Scope
T 5783 specifies the dimensions and tolerances of hex bolt, fully threaded — gb/t 5783 / iso 4017 (series 011). Material, property class, surface finish and packaging are governed by separate documents in the same standards family (for example ISO 898-1 for the mechanical property classes of bolts and screws).
Tolerance & Product Grades
T 5783, alongside the related GB/T 5783 / ISO 4017 entries on this site, specifies product grades (typically A or B for fine work and C for general engineering) and tolerance classes for the controlling dimensions. Choose the grade against the precision your application requires.
Dimensions Specified by T 5783
| Size | Pitch (mm) | Nominal diameter d (mm) | Length L (mm) | Width across flats s (mm) | Width across corners e (mm) | Head height k (mm) |
|---|---|---|---|---|---|---|
| M3 | 0.5 | 3 | 20 | 5.5 | 6.01 | 2.0 |
| M4 | 0.7 | 4 | 25 | 7.0 | 7.66 | 2.8 |
| M5 | 0.8 | 5 | 30 | 8.0 | 8.79 | 3.5 |
| M6 | 1.0 | 6 | 40 | 10.0 | 11.05 | 4.0 |
| M8 | 1.25 | 8 | 50 | 13.0 | 14.38 | 5.3 |
| M10 | 1.5 | 10 | 60 | 16.0 | 17.77 | 6.4 |
| M12 | 1.75 | 12 | 80 | 18.0 | 20.03 | 7.5 |
| M14 | 2.0 | 14 | 80 | 21.0 | 23.36 | 8.8 |
| M16 | 2.0 | 16 | 100 | 24.0 | 26.75 | 10.0 |
| M18 | 2.5 | 18 | 100 | 27.0 | 30.14 | 11.5 |
| M20 | 2.5 | 20 | 120 | 30.0 | 33.53 | 12.5 |
| M24 | 3.0 | 24 | 150 | 36.0 | 39.98 | 15.0 |
| M30 | 3.5 | 30 | 180 | 46.0 | 50.85 | 18.7 |
| M36 | 4.0 | 36 | 200 | 55.0 | 60.79 | 22.5 |
Equivalent Standards
Where direct equivalents exist (ISO ↔ DIN, ISO ↔ ASME), they are listed on the parent Hex Bolt, Fully Threaded — GB/T 5783 / ISO 4017 (Series 011) page. Always confirm against the dimensions on this page, since some "equivalent" standards differ in tolerances and head geometry.
Companion Standards
T 5783 controls only the geometry of hex bolt, fully threaded — gb/t 5783 / iso 4017 (series 011). The mechanical strength is set by ISO 898-1 (bolts and screws) or ISO 898-2 (nuts); the surface finish is governed by separate finish standards (e.g. ISO 4042 for electroplating). For corrosion testing, the relevant document is ISO 9227 (neutral salt spray).