Skip to content
info@engineeringhardware.com
WhatsApp
Request a Quote
Screws · Trade series (hardened high-low thread) · Application guide

What Are Concrete Screws, Hex Washer Head Used For?

Typical applications, the industries that specify concrete screws, hex washer head, and how to choose the right size, material and finish for the joint.

Concrete Screws, Hex Washer Head are used for fixing into sheet, timber or plastic by forming their own thread as they are driven, without a tapped hole. They are manufactured to Trade series (hardened high-low thread), and selection is driven by the screw size, the fit and tolerance the assembly requires, and the service environment.

Primary duty
Fixing into sheet, timber or plastic by forming their own thread as they are driven, without a tapped hole
Governing standard
Trade series (hardened high-low thread)
Screw size range
6.3 to 12.5
Category
Screws

Application notes are general engineering guidance. Verify the property class and any approval requirement against your own design calculation.

What Are Concrete Screws, Hex Washer Head Used For? application image

Concrete Screws, Hex Washer Head are used primarily for fixing into sheet, timber or plastic by forming their own thread as they are driven, without a tapped hole. This page lists the industries and assemblies where they are specified, the selection criteria that matter for each application, installation practice, and the cases where a different fastener type is the correct choice. Parts are supplied to Trade series (hardened high-low thread). Stocked across roughly 6.3 to 12.5, they cover general to heavy-duty work.

Typical Applications for Concrete Screws, Hex Washer Head

The most common settings where these are specified:

  • Maintenance & repair (MRO): a stocked size for servicing existing plant where the original fastener spec must be matched.
  • Fabrication & metalwork: bench and on-site assembly of steel frames, enclosures and weldments.
  • Electronics & enclosures: mounting PCBs, panels and lids where the drive style and head height matter.
  • Appliances & consumer goods: high-volume assembly with power tools and consistent seating.
  • Machine guarding & panels: removable access covers that are opened for service.

How to Specify Concrete Screws, Hex Washer Head for Your Application

  • Size: Match the nominal size to the mating thread or hole. This product spans 6.3–12.5; check the full table below for the exact dimensions of each size.
  • Drive & head: Pick the drive (socket, cross, slot) and head style for the tool access and seating surface; a recessed drive resists cam-out under power tools.
  • Environment: For damp, coastal or chemical exposure prefer A4/316 stainless or a suitable coating; indoors, plated steel or A2 is usually sufficient.
  • Standard: This product is supplied to Trade series (hardened high-low thread). Quoting the standard on your order guarantees interchangeable dimensions between suppliers.

Installation & Assembly Practice

  • Match the driver exactly to the recess (PH ≠ PZ; hex key sizes per ISO 2936) and keep the tool axial — side load is the main cause of stripped drives.
  • In tapped holes, engage a thread length of at least 1× the nominal diameter in steel, 2× in aluminum.
  • Set power tools to a torque that seats the head without embedding it into the mating surface.

Common Selection Mistakes with Concrete Screws, Hex Washer Head

  • Under-sizing the drive for the installation torque — a small recess at high torque strips before the screw is seated.
  • Using a countersunk head in thin sheet where the countersink removes most of the load-bearing material.
  • Specifying stainless in high-strength duty: A2-70 is roughly class 7 steel, not a 10.9 substitute.

Where Concrete Screws, Hex Washer Head Are Not the Right Choice

Not for high-preload structural joints (use a property-class bolt and nut), and not in thin sheet where a self-drilling or self-tapping type suits better.

Technical Drawing

Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.

Sends the selected values to the quote form below.

Request a Quote

The form below follows the current technical drawing configuration. Change the drawing values above and the request details update automatically.

Request a Quotation

Specification
Business Information

Dimensions & Specifications (Trade series (hardened high-low thread))

Nominal diameter d (mm)Drill hole diameter (mm)Across flats s (mm)Head height k (mm)Minimum embedment (mm)Common length range (mm)Base materialFinish
6.35.085.02540~100Concrete / solid masonryBlue Ruspert
7.56.0105.53050~150Concrete / solid masonryBlue Ruspert
10.08.0137.04060~200ConcreteZinc flake
12.510.0178.55080~250ConcreteZinc flake
Inside the plant

Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

  1. Wire rod feeding into a cold heading machine
    01

    Cold heading

    Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.

    Head dimensions and under-head radius checked at set-up and per shift.

  2. Thread rolling machine producing bolt threads
    02

    Thread rolling

    Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.

    Go / no-go ring gauges to ISO 965 tolerance class 6g.

  3. Baskets of bolts staged for heat treatment
    03

    Heat treatment

    Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.

    Core hardness and tensile tested per lot to ISO 898-1.

  4. Zinc plated bolts in a treatment basket
    04

    Surface treatment

    Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.

    Coating thickness and neutral salt spray hours to ISO 9227.

Frequently Asked Questions

Which industries use Concrete Screws, Hex Washer Head?

They are commonly specified in maintenance & repair (mro), fabrication & metalwork and electronics & enclosures, among other sectors.

How do I choose the right size of Concrete Screws, Hex Washer Head?

Match the nominal size to the mating thread or hole. This product is available from 6.3 to 12.5; the full dimension table on this page lists each size.

What drive type do Concrete Screws, Hex Washer Head use?

Drive depends on the head style — socket (hex key), cross (Phillips/Pozi) or slot. A recessed drive resists cam-out when driven with power tools; check the product head style on this page.

What material should Concrete Screws, Hex Washer Head be for outdoor use?

For damp, coastal or chemical environments specify A4 (316) stainless or a suitably coated steel. For indoor or dry use, A2 (304) stainless or zinc-plated steel is normally adequate.

Can I get a quote for Concrete Screws, Hex Washer Head in the size and material I need?

Yes. Use the technical drawing and quote form on this page to set the size and options, then send the exact configuration to our team for pricing and lead time.