Nyloc Lock Nuts manufactured in A2 Stainless Steel (ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70) are dimensioned to DIN 985 / ISO 7040. The sections below give the mechanical and physical properties of the grade, its behavior in corrosive and elevated-temperature service, and the full size table.
Why Choose A2 Stainless Steel for Nyloc Lock Nuts
The most common stainless group for indoor and general outdoor fasteners. For nyloc lock nuts, this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Good general corrosion resistance |
Corrosion Behavior in Service
A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Nyloc Lock Nuts in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).
Comparable Grades
For Nyloc Lock Nuts, the alternative stainless grade is A4 (316). The practical dividing line is chlorides: A2 (304) is fine until salt is involved, and A4 (316) exists for the cases where it is — coastal, marine and road-salt service. Neither reaches the strength of a plated class 8.8 or 10.9 fastener.
Using Stainless Fasteners in Aluminum
The galvanic couple here runs the wrong way: aluminum is the less noble metal, so it corrodes and the fastener does not. What governs the rate is the ratio of areas — a large anode and a small cathode is a tolerable combination, the reverse concentrates the attack into thin material around the hole. An isolating washer plus sealant breaks the circuit; where that is impractical, match the fastener to the substrate.
Sizes of Nyloc Lock Nuts Available in A2 Stainless Steel
| Size | Pitch (mm) | Width across flats s (mm) | Width across corners e min (mm) | Total height m (mm) | Metal height (mm) | Reference standard | Notes |
|---|---|---|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 6.01 | 4.0 | 2.4 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M4 | 0.7 | 7.0 | 7.66 | 5.0 | 3.2 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M5 | 0.8 | 8.0 | 8.79 | 5.0 | 3.7 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M6 | 1.0 | 10.0 | 11.05 | 6.0 | 4.7 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M8 | 1.25 | 13.0 | 14.38 | 8.0 | 6.14 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M10 | 1.5 | 16.0 | 17.77 | 10.0 | 8.04 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M12 | 1.75 | 18.0 | 20.03 | 12.0 | 9.64 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M14 | 2.0 | 21.0 | 23.36 | 14.0 | 11.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M16 | 2.0 | 24.0 | 26.75 | 16.0 | 13.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M20 | 2.5 | 30.0 | 32.95 | 20.0 | 16.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M24 | 3.0 | 36.0 | 39.55 | 22.0 | 19.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M30 | 3.5 | 46.0 | 50.85 | 25.0 | 24.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M36 | 4.0 | 55.0 | 60.79 | 29.0 | 29.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
Dimensions are independent of the material: every size above is available in A2 Stainless Steel.
Custom manufacturing · Made to drawing
Need this nut in a grade that is not listed?
A2 Stainless Steel is one of the grades the catalog describes. Locking method is specifiable independently of the rest: nylon insert, all-metal deformed thread, serrated flange, or none. Made by cold heading or tapping.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
