A2 Stainless Steel Pan Head Screws pairs the standard ISO 1207 / ISO 7045 / DIN 7985 with a A2 Stainless Steel base material. The sections below cover why engineers select this grade for pan head screws, its corrosion and temperature behavior, and the sizes available.
Why Choose A2 Stainless Steel for Pan Head Screws
The most common stainless grade for indoor and general outdoor fasteners. For pan head screws, this matters when good general corrosion resistance is the primary requirement.
Mechanical & Physical Properties
| Grade designation | A2-70 (304) |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C |
| Corrosion characteristic | Good general corrosion resistance |
Corrosion Behavior in Service
A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Pan Head Screws in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).
Galvanic & Galling Considerations
Two important notes for stainless pan head screws: (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Sizes of Pan Head Screws Available in A2 Stainless Steel
| Size | Pitch (mm) | Head diameter dk (mm) | Head height k (mm) | Cross recess | Reference standard |
|---|---|---|---|---|---|
| M1 | 0.25 | 2.0 | 0.8 | PH0 | ISO 1207 / ISO 7045 / DIN 7985 |
| M1.2 | 0.25 | 2.3 | 0.9 | PH0 | ISO 1207 / ISO 7045 / DIN 7985 |
| M1.4 | 0.3 | 2.6 | 1.0 | PH0 | ISO 1207 / ISO 7045 / DIN 7985 |
| M1.6 | 0.35 | 3.0 | 1.0 | PH0 | ISO 1207 / ISO 7045 / DIN 7985 |
| M2 | 0.4 | 3.8 | 1.3 | PH1 | ISO 1207 / ISO 7045 / DIN 7985 |
| M2.5 | 0.45 | 4.7 | 1.5 | PH1 | ISO 1207 / ISO 7045 / DIN 7985 |
| M3 | 0.5 | 5.6 | 1.8 | PH1 | ISO 1207 / ISO 7045 / DIN 7985 |
| M3.5 | 0.6 | 6.5 | 2.1 | PH2 | ISO 1207 / ISO 7045 / DIN 7985 |
| M4 | 0.7 | 8.0 | 2.4 | PH2 | ISO 1207 / ISO 7045 / DIN 7985 |
| M5 | 0.8 | 9.5 | 3.0 | PH2 | ISO 1207 / ISO 7045 / DIN 7985 |
| M6 | 1.0 | 12.0 | 3.6 | PH3 | ISO 1207 / ISO 7045 / DIN 7985 |
| M8 | 1.25 | 16.0 | 4.8 | PH3 | ISO 1207 / ISO 7045 / DIN 7985 |
| M10 | 1.5 | 20.0 | 6.0 | PH4 | ISO 1207 / ISO 7045 / DIN 7985 |