A4 Stainless Steel Thin Hex Nut combine the dimensional form of GB/T 6172.1 / ISO 4035 with the material properties of grade ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80: superior, including marine and chloride environments, largely non-magnetic, service range approx. -200 °C to +400 °C, subject to the property class and the joint. This page summarizes the grade data, its corrosion behavior in service, the comparable grades, and the sizes supplied.
Why Choose A4 Stainless Steel for Thin Hex Nut — GB/T 6172.1 / ISO 4035 (Series 055)
Specified for marine, coastal and chemical applications. For thin hex nut — gb/t 6172.1 / iso 4035 (series 055), this matters when superior, including marine and chloride environments is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 3506 group A4 (316 / 1.4401), commonly supplied A4-80 |
|---|---|
| Magnetic response | Largely non-magnetic |
| Service temperature | approx. -200 °C to +400 °C, subject to the property class and the joint |
| Corrosion characteristic | Superior, including marine and chloride environments |
Galvanic & Galling Considerations
Two important notes for stainless thin hex nut — gb/t 6172.1 / iso 4035 (series 055): (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.
Comparable Grades
For Thin Hex Nut — GB/T 6172.1 / ISO 4035 (Series 055), the alternative stainless grade is A2 (304). Choose A2 (304) for general use and A4 (316) wherever chlorides are present; the molybdenum in A4 is the whole difference. Remember that stainless is the corrosion answer, not the strength answer — for load, look at class 8.8 or 10.9 instead.
Using Stainless Fasteners in Aluminum
Stainless steel is more noble than aluminum, so with an electrolyte present — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. Area ratio decides how bad it gets: a small stainless fastener in a large aluminum section is normally acceptable, a large stainless fastener in thin aluminum is not. Where the joint gets wet, isolate the metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.
Sizes of Thin Hex Nut — GB/T 6172.1 / ISO 4035 (Series 055) Available in A4 Stainless Steel
| Size | Pitch (mm) | Width across flats s (mm) | Width across corners e (mm) | Nut height m (mm) | Reference standard |
|---|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 6.01 | 1.8 | ISO 4035 / GB/T 6172 |
| M4 | 0.7 | 7.0 | 7.66 | 2.2 | ISO 4035 / GB/T 6172 |
| M5 | 0.8 | 8.0 | 8.79 | 2.7 | ISO 4035 / GB/T 6172 |
| M6 | 1.0 | 10.0 | 11.05 | 3.2 | ISO 4035 / GB/T 6172 |
| M8 | 1.25 | 13.0 | 14.38 | 4.0 | ISO 4035 / GB/T 6172 |
| M10 | 1.5 | 16.0 | 17.77 | 5.0 | ISO 4035 / GB/T 6172 |
| M12 | 1.75 | 18.0 | 20.03 | 6.0 | ISO 4035 / GB/T 6172 |
| M14 | 2.0 | 21.0 | 23.36 | 7.0 | ISO 4035 / GB/T 6172 |
| M16 | 2.0 | 24.0 | 26.75 | 8.0 | ISO 4035 / GB/T 6172 |
| M18 | 2.5 | 27.0 | 30.14 | 9.0 | ISO 4035 / GB/T 6172 |
| M20 | 2.5 | 30.0 | 33.53 | 10.0 | ISO 4035 / GB/T 6172 |
| M24 | 3.0 | 36.0 | 39.98 | 12.0 | ISO 4035 / GB/T 6172 |
| M30 | 3.5 | 46.0 | 50.85 | 15.0 | ISO 4035 / GB/T 6172 |
| M36 | 4.0 | 55.0 | 60.79 | 18.0 | ISO 4035 / GB/T 6172 |
Dimensions are independent of the material: every size above is available in A4 Stainless Steel.
Custom manufacturing · Made to drawing
Need this nut in a grade that is not listed?
A4 Stainless Steel is one of the grades the catalog describes. Thread, height, across-flats, property class, locking feature and flange form can all be varied, including thread sizes the standard series does not run to. Made by cold heading or tapping.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
