Property Class 12.9 Steel Bicycle Cleat Fixing Bolts are supplied to ISO 898-1 property class 12.9. Corrosion behaviour is requires plating or black-oxide protection, the material is magnetic, and the usable service range is commonly limited to approx. +300 °C; confirm against the coating and the load. In practice this grade is the highest common strength class, for high-load machine assembly.
- Grade
- ISO 898-1 property class 12.9
- Corrosion resistance
- Requires plating or black-oxide protection
- Magnetic response
- Magnetic
- Service temperature
- commonly limited to approx. +300 °C; confirm against the coating and the load
Property values are typical for the grade. Certified mechanical test data is available on request for production orders.
Property Class 12.9 Steel Bicycle Cleat Fixing Bolts are supplied to our own published dimensions — this is a trade-series article rather than one covered by a dimensional standard, so confirm the figures against the part you are replacing. The grade provides requires plating or black-oxide protection and is magnetic; the practical service range is commonly limited to approx. +300 °C; confirm against the coating and the load.
Why Choose Property Class 12.9 Steel for Bicycle Cleat Fixing Bolts
The highest common strength class, for high-load machine assembly. For bicycle cleat fixing bolts, this matters when requires plating or black-oxide protection is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 898-1 property class 12.9 |
|---|
| Magnetic response | Magnetic |
|---|
| Service temperature | commonly limited to approx. +300 °C; confirm against the coating and the load |
|---|
| Corrosion characteristic | Requires plating or black-oxide protection |
|---|
Galvanic & Galling Considerations
For bicycle cleat fixing bolts in steel, the dominant compatibility issue is hydrogen embrittlement at high property classes (10.9 and above) when electroplated. Plating must be followed by an appropriate baking treatment, or a non-electroplated finish (mechanical zinc, zinc flake) should be substituted.
Comparable Grades
For Bicycle Cleat Fixing Bolts, class 8.8 is the comparable strength step. Move up when the joint preload approaches the proof load of the current class; move down when the joint is over-specified. For corrosion-critical service, switch to stainless A2 or A4.
Sizes of Bicycle Cleat Fixing Bolts Available in Property Class 12.9 Steel
| Thread size | Length options (mm) | Drive | Typical cleat system | Provisional torque (N·m) | Selection rule |
|---|
| M5 | 8 / 10 / 13.5 | 4 mm hex | road cleat hardware | | match shoe and cleat stack |
| M5 | about 12.5 example | 4 mm hex | two-bolt cleat hardware | about 2.5 provisional | follow the cleat and shoe service instruction |
Dimensions are independent of the material: every size above is available in Property Class 12.9 Steel.
Custom manufacturing · Made to drawing
Need this bolt in a grade that is not listed?
Grade 12 9 Steel is one of the grades the catalog describes. Material and finish are usually what drives a special — a grade the standard part is not stocked in, or a coating chosen against a salt-spray figure instead of a default. Made by cold heading or hot forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
Custom bolt manufacturingSend a drawing
Applications & Industries
What Bicycle Cleat Fixing Bolts are specified for, industry by industry.
Industries that specify Bicycle Cleat Fixing Bolts
-
Service shops
4 mm hex sets support controlled cleat replacement.
-
Performance cycling
Provisional torque is followed from the cleat and shoe instruction.
-
Cycling footwear
M5 cleat screws attach road and two-bolt cleats to the shoe plate.
-
Bike fitting
Length follows the cleat, washer and shoe-stack thickness.
-
Steel fabrication
Bolted connections in frames, enclosures, walkways and weldments, on the bench and on site.
-
Energy & infrastructure
Tower, pipework, switchgear and plant fixings specified for long service life and inspectable joints.
Typical applications
- checking washer and head seating
- using the specified provisional and final torque
- fastening an M5 cleat to a cycling shoe
- choosing 8, 10 or 13.5 mm from the cleat stack
- assemblies that are dismantled for service and re-torqued
- joints where the property class is stated on the drawing
Service conditions to specify against
- Marine and coastal
- Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- High load
- Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- Torque and preload
- The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together.
Where to use something else
- Do not select a cleat screw solely by the old screw length; shoe plate thickness and cleat model can change engagement.
- Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material.
Full application guide: where Bicycle Cleat Fixing Bolts are used, how to specify them, and the cases they are wrong for