Property Class 8.8 Steel Bicycle Cleat Fixing Bolts are supplied to ISO 898-1 property class 8.8. Corrosion behaviour is requires plating (zinc) for corrosion protection, the material is magnetic, and the usable service range is commonly limited to approx. +300 °C; confirm against the coating and the load. In practice this grade is the workhorse medium-carbon alloy class for structural joints.
- Grade
- ISO 898-1 property class 8.8
- Corrosion resistance
- Requires plating (zinc) for corrosion protection
- Magnetic response
- Magnetic
- Service temperature
- commonly limited to approx. +300 °C; confirm against the coating and the load
Property values are typical for the grade. Certified mechanical test data is available on request for production orders.
Material page for bicycle cleat fixing bolts in Property Class 8.8 Steel (ISO 898-1 property class 8.8). The sizes below are the ones we supply; there is no published dimensional standard for this article, so the table rather than a standard number is what to quote. Corrosion behaviour is requires plating (zinc) for corrosion protection and the service range is commonly limited to approx. +300 °C; confirm against the coating and the load.
Why Choose Property Class 8.8 Steel for Bicycle Cleat Fixing Bolts
The workhorse medium-carbon alloy class for structural joints. For bicycle cleat fixing bolts, this matters when requires plating (zinc) for corrosion protection is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 898-1 property class 8.8 |
|---|
| Magnetic response | Magnetic |
|---|
| Service temperature | commonly limited to approx. +300 °C; confirm against the coating and the load |
|---|
| Corrosion characteristic | Requires plating (zinc) for corrosion protection |
|---|
Corrosion Behavior in Service
Carbon and alloy steel bicycle cleat fixing bolts require a coating for corrosion protection. Zinc plating (with or without passivation) is the most common; hot-dip galvanizing is used for outdoor structural service; black-oxide is mainly a tarnish-prevention finish for tool-room use.
Comparable Grades
For Bicycle Cleat Fixing Bolts, class 10.9 or 12.9 is the comparable strength step. Move up when the joint preload approaches the proof load of the current class; move down when the joint is over-specified. For corrosion-critical service, switch to stainless A2 or A4.
Sizes of Bicycle Cleat Fixing Bolts Available in Property Class 8.8 Steel
| Thread size | Length options (mm) | Drive | Typical cleat system | Provisional torque (N·m) | Selection rule |
|---|
| M5 | 8 / 10 / 13.5 | 4 mm hex | road cleat hardware | | match shoe and cleat stack |
| M5 | about 12.5 example | 4 mm hex | two-bolt cleat hardware | about 2.5 provisional | follow the cleat and shoe service instruction |
Dimensions are independent of the material: every size above is available in Property Class 8.8 Steel.
Custom manufacturing · Made to drawing
Need this bolt in a grade that is not listed?
Grade 8 8 Steel is one of the grades the catalog describes. Head form and drive can be specified to the assembly rather than to a standard: a larger bearing face, a security drive, or a socket sized for the tool already on the bench. Made by cold heading or hot forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
Custom bolt manufacturingSend a drawing
Applications & Industries
What Bicycle Cleat Fixing Bolts are specified for, industry by industry.
Industries that specify Bicycle Cleat Fixing Bolts
-
Service shops
4 mm hex sets support controlled cleat replacement.
-
Performance cycling
Provisional torque is followed from the cleat and shoe instruction.
-
Cycling footwear
M5 cleat screws attach road and two-bolt cleats to the shoe plate.
-
Bike fitting
Length follows the cleat, washer and shoe-stack thickness.
-
Steel fabrication
Bolted connections in frames, enclosures, walkways and weldments, on the bench and on site.
-
Energy & infrastructure
Tower, pipework, switchgear and plant fixings specified for long service life and inspectable joints.
Typical applications
- checking washer and head seating
- using the specified provisional and final torque
- fastening an M5 cleat to a cycling shoe
- choosing 8, 10 or 13.5 mm from the cleat stack
- assemblies that are dismantled for service and re-torqued
- joints where the property class is stated on the drawing
Service conditions to specify against
- Marine and coastal
- Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- High load
- Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- Torque and preload
- The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together.
Where to use something else
- Do not select a cleat screw solely by the old screw length; shoe plate thickness and cleat model can change engagement.
- Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material.
Full application guide: where Bicycle Cleat Fixing Bolts are used, how to specify them, and the cases they are wrong for