For nyloc lock nuts in Property Class 12.9 Steel, the controlling selection factors are corrosion exposure, strength requirement and service temperature. The grade data for Property Class 12.9 Steel (ISO 898-1 property class 12.9) is summarized below together with every size supplied.
Why Choose Property Class 12.9 Steel for Nyloc Lock Nuts
The highest common strength class, for high-load machine assembly. For nyloc lock nuts, this matters when requires plating or black-oxide protection is the primary requirement.
Mechanical & Physical Properties
| Grade designation | ISO 898-1 property class 12.9 |
|---|---|
| Magnetic response | Magnetic |
| Service temperature | commonly limited to approx. +300 °C; confirm against the coating and the load |
| Corrosion characteristic | Requires plating or black-oxide protection |
Corrosion Behavior in Service
Carbon and alloy steel nyloc lock nuts require a coating for corrosion protection. Zinc plating (with or without passivation) is the most common; hot-dip galvanizing is used for outdoor structural service; black-oxide is mainly a tarnish-prevention finish for tool-room use.
Galvanic & Galling Considerations
For nyloc lock nuts in steel, the dominant compatibility issue is hydrogen embrittlement at high property classes (10.9 and above) when electroplated. Plating must be followed by an appropriate baking treatment, or a non-electroplated finish (mechanical zinc, zinc flake) should be substituted.
Sizes of Nyloc Lock Nuts Available in Property Class 12.9 Steel
| Size | Pitch (mm) | Width across flats s (mm) | Width across corners e min (mm) | Total height m (mm) | Metal height (mm) | Reference standard | Notes |
|---|---|---|---|---|---|---|---|
| M3 | 0.5 | 5.5 | 6.01 | 4.0 | 2.4 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M4 | 0.7 | 7.0 | 7.66 | 5.0 | 3.2 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M5 | 0.8 | 8.0 | 8.79 | 5.0 | 3.7 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M6 | 1.0 | 10.0 | 11.05 | 6.0 | 4.7 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M8 | 1.25 | 13.0 | 14.38 | 8.0 | 6.14 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M10 | 1.5 | 16.0 | 17.77 | 10.0 | 8.04 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M12 | 1.75 | 18.0 | 20.03 | 12.0 | 9.64 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M14 | 2.0 | 21.0 | 23.36 | 14.0 | 11.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M16 | 2.0 | 24.0 | 26.75 | 16.0 | 13.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M20 | 2.5 | 30.0 | 32.95 | 20.0 | 16.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M24 | 3.0 | 36.0 | 39.55 | 22.0 | 19.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M30 | 3.5 | 46.0 | 50.85 | 25.0 | 24.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
| M36 | 4.0 | 55.0 | 60.79 | 29.0 | 29.0 | DIN 985 / ISO 7040 | With nylon insert, single use |
Dimensions are independent of the material: every size above is available in Property Class 12.9 Steel.
Custom manufacturing · Made to drawing
Need this nut in a grade that is not listed?
Grade 12 9 Steel is one of the grades the catalog describes. Height and across-flats are the two most often changed — a thinner nut for clearance, a larger hex for a tool that is already on the line. Made by cold heading or tapping.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
