Seals · Trade series (anaerobic adhesives for threaded assemblies)

NBR (Nitrile) Anaerobic Threadlockers and Thread Sealants

Temperature range, chemical and fluid compatibility, hardness and the full dimensional range for this compound.

NBR (Nitrile) Anaerobic Threadlockers and Thread Sealants are supplied to acrylonitrile-butadiene rubber, typically 70 Shore A. Corrosion behaviour is good resistance to mineral oil, grease and hydraulic fluid; poor in ozone and weathering, the material is non-magnetic, and the usable service range is approx. -30 °C to +100 °C. In practice this grade is the default elastomer for oil and hydraulic sealing.

Grade: acrylonitrile-butadiene rubber, typically 70 Shore A
Corrosion resistance: Good resistance to mineral oil, grease and hydraulic fluid; poor in ozone and weathering
Magnetic response: Non-magnetic
Service temperature: approx. -30 °C to +100 °C

Property values are typical for the grade. Certified mechanical test data is available on request for production orders.

Anaerobic Threadlockers and Thread Sealants manufactured in NBR (Nitrile) (acrylonitrile-butadiene rubber, typically 70 Shore A) are dimensioned to Trade series (anaerobic adhesives for threaded assemblies). The sections below give the mechanical and physical properties of the grade, its behavior in corrosive and elevated-temperature service, and the full size table.

Why Choose NBR (Nitrile) for Anaerobic Threadlockers and Thread Sealants

The default elastomer for oil and hydraulic sealing. For anaerobic threadlockers and thread sealants, this matters when good resistance to mineral oil, grease and hydraulic fluid; poor in ozone and weathering is the primary requirement.

Mechanical & Physical Properties

Grade designation	acrylonitrile-butadiene rubber, typically 70 Shore A
Magnetic response	Non-magnetic
Service temperature	approx. -30 °C to +100 °C
Corrosion characteristic	Good resistance to mineral oil, grease and hydraulic fluid; poor in ozone and weathering

Corrosion Behavior in Service

Carbon and alloy steel anaerobic threadlockers and thread sealants require a coating for corrosion protection. Zinc plating (with or without passivation) is the most common; hot-dip galvanizing is used for outdoor structural service; black-oxide is mainly a tarnish-prevention finish for tool-room use.

Comparable Grades

For anaerobic threadlockers and thread sealants, consider FKM where temperature or chemical exposure is higher, or EPDM where the medium is water, steam or brake fluid rather than oil. Elastomer selection is decided by the medium, the temperature range and whether the seal is static or dynamic — not by strength.

Sizes of Anaerobic Threadlockers and Thread Sealants Available in NBR (Nitrile)

Grade	Removal	Typical use	Notes
low strength	hand tools	set screws, adjusting screws, small fasteners	up to about M12
medium strength	hand tools	general assembly, machine screws	the usual default
high strength	heat and hand tools	studs, permanent assemblies	not for parts serviced in the field
thread sealant grade	hand tools	tapered pipe threads, hydraulic fittings	seals rather than locks
retaining compound	heat	bearings, bushes, cylindrical fits	not a thread product

Technical Drawing

Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.

Sends the selected values to the quote form below.

Request a Quote

The form below follows the current technical drawing configuration. Change the drawing values above and the request details update automatically.

Request a Quotation

Specification

Item / category Standard Size(s) Material / finish Quantity

Business Information

Company * Contact Name * Email * Phone (with country code) Country / Region

Notes

Dimensions & Specifications (Trade series (anaerobic adhesives for threaded assemblies))

Grade	Removal	Typical use	Notes
low strength	hand tools	set screws, adjusting screws, small fasteners	up to about M12
medium strength	hand tools	general assembly, machine screws	the usual default
high strength	heat and hand tools	studs, permanent assemblies	not for parts serviced in the field
thread sealant grade	hand tools	tapered pipe threads, hydraulic fittings	seals rather than locks
retaining compound	heat	bearings, bushes, cylindrical fits	not a thread product

Applications & Industries

Anaerobic Threadlockers and Thread Sealants are bought for a small number of well-defined jobs. These are the ones we ship them for. Stocked from low strength to retaining compound (inside diameter).

Industries that specify Anaerobic Threadlockers and Thread Sealants

Field maintenance Securing set screws.
Machine assembly Fasteners that must not loosen.
Automotive Vibration-prone joints.
Hydraulics Tapered thread sealing.
Process & food equipment Sealing at joints that are cleaned and inspected.
Hydraulics & pneumatics Static and dynamic sealing in cylinders and valve bodies.

Typical applications

allowing the stated cure time before loading the joint
choosing the grade by how the joint will be serviced
degreasing both threads before applying
using a sealant grade rather than a locking grade on pipe threads
excluding dust and moisture from a housing
sealing a joint against fluid or air pressure

Service conditions to specify against

Sealed joints: Used where the fixing has to keep water or air out as well as hold — the elastomer, not the fastener, decides service life.
Vibration: Specified where cyclic load would loosen a plain nut or screw — rotating plant, rail, mobile equipment and anything that is not re-torqued in service.

Where to use something else

Do not use a high-strength grade on anything that will be serviced in the field; removing it needs heat, and heat is rarely available where the fastener has to come out.

Full application guide: where Anaerobic Threadlockers and Thread Sealants are used, how to specify them, and the cases they are wrong for

Inside the plant

Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

01

Cold heading

Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.

Head dimensions and under-head radius checked at set-up and per shift.
02

Thread rolling

Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.

Go / no-go ring gauges to ISO 965 tolerance class 6g.
03

Heat treatment

Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.

Core hardness and tensile tested per lot to ISO 898-1.
04

Surface treatment

Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.

Coating thickness and neutral salt spray hours to ISO 9227.

Frequently Asked Questions

What's the service temperature limit for NBR (Nitrile)?

The practical service range is approx. -30 °C to +100 °C.

Can NBR (Nitrile) replace stainless steel structurally?

No — stainless A2/A4 cannot match class 10.9 / 12.9 strength. Stainless is selected for corrosion, not raw strength.

Are NBR (Nitrile) Anaerobic Threadlockers and Thread Sealants magnetic?

NBR (Nitrile) Anaerobic Threadlockers and Thread Sealants are non-magnetic.

What corrosion resistance do NBR (Nitrile) Anaerobic Threadlockers and Thread Sealants offer?

NBR (Nitrile) Anaerobic Threadlockers and Thread Sealants provide good resistance to mineral oil, grease and hydraulic fluid; poor in ozone and weathering with a service range of approx. -30 °C to +100 °C.

How do I request a quotation?

Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.