This page covers M12 Hex Socket Cone Point Set Screw to GB/T 78 / ISO 4027: the full dimensional row, hole and tool sizes, proof-load data and typical applications. All values are taken from the governing standards (GB/T 78 / ISO 4027 together with ISO 273, ISO 724 and ISO 898-1 where applicable).
M12 Dimensional Row (GB/T 78 / ISO 4027)
| Size | Pitch (mm) | Length L (mm) | Hex socket s (mm) | Engagement depth t min (mm) | Point diameter dp (mm) | Reference standard |
|---|---|---|---|---|---|---|
| M12 | 1.75 | 18 | 6.0 | 6.0 | 8.5 | ISO 4026-4029 / GB/T 77-79 |
Spanner & Drive for M12 Hex Socket Cone Point Set Screw — GB/T 78 / ISO 4027 (Series 027)
The hex socket for M12 Hex Socket Cone Point Set Screw — GB/T 78 / ISO 4027 (Series 027) is shown in the spec table — use the matching Allen / hex key (an ISO 2936 hex key set covers the full range). For a one-off, a T-handle key and a calibrated arm will do. For a batch, the only way to get the same preload twice is a torque-controlled driver.
Hole Sizes for M12
| Coarse-thread pitch (ISO 724) | 1.75 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 13.5 mm |
| Tapping drill, coarse thread | 10.25 mm |
Tightening Torque for M12
| Class 8.8 (dry, ~µ 0.125) | ≈ 84 Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ 124 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 145 Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M12
Set screws are rated to ISO 898-5 by hardness, because they work in compression against a shaft rather than in tension. ISO 898-1 excludes them, and a set screw has no head to preload against, so neither a property class nor a preload torque applies. Seating torque depends on the point form and the shaft material.
M12 Hex Socket Cone Point Set Screw — GB/T 78 / ISO 4027 (Series 027) Weight
A steel M12 hex socket cone point set screw at the listed 18 mm length weighs approximately 8.0 g each — about 8.0 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³).
Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Installation Tips for M12 Hex Socket Cone Point Set Screw — GB/T 78 / ISO 4027 (Series 027)
- Use a quality Allen key fully seated in the socket — partial engagement is the most common cause of stripped sockets at this size.
- For countersunk and button-head variants, chamfer the through-hole to seat the head flush without preloading the head/shank fillet.
Mating Parts for M12
For M12, pair with a M12 hex nut (ISO 4032 / DIN 934) and, where used, a M12 flat washer (ISO 7089 / DIN 125A) under the head and under the nut.
Custom manufacturing · Made to drawing
Need hex socket cone point set screw in a size this table does not list?
This page covers M12 hex socket cone point set screw. Material and finish are usually what drives a special — a grade the standard part is not stocked in, or a coating chosen against a salt-spray figure instead of a default. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
