Dimensional and assembly data for M20 Hex Socket Cone Point Set Screw to GB/T 78 / ISO 4027. Includes head size and width across flats, clearance-hole and tapping-drill diameters, tightening torque per property class, and the sizes to step up or down to when the joint requires it.
M20 Dimensional Row (GB/T 78 / ISO 4027)
| Size | Pitch (mm) | Length L (mm) | Hex socket s (mm) | Engagement depth t min (mm) | Point diameter dp (mm) | Reference standard |
|---|---|---|---|---|---|---|
| M20 | 2.5 | 30 | 10.0 | 10.0 | 15.0 | ISO 4026-4029 / GB/T 77-79 |
Spanner & Drive for M20 Hex Socket Cone Point Set Screw — GB/T 78 / ISO 4027 (Series 027)
The hex socket for M20 Hex Socket Cone Point Set Screw — GB/T 78 / ISO 4027 (Series 027) is shown in the spec table — use the matching Allen / hex key (an ISO 2936 hex key set covers the full range). A T-handle Allen key gives the best feel for setting preload by feel; for production work use a torque-controlled driver.
Hole Sizes for M20
| Coarse-thread pitch (ISO 724) | 2.5 mm |
|---|---|
| Through-hole / clearance (ISO 273 medium) | 22 mm |
| Tapping drill, coarse thread | 17.5 mm |
Tightening Torque for M20
| Class 8.8 (dry, ~µ 0.125) | ≈ 410 Nm |
|---|---|
| Class 10.9 (dry, ~µ 0.125) | ≈ 580 Nm |
| Class 12.9 (dry, ~µ 0.125) | ≈ 690 Nm |
Indicative dry-joint values. Lubrication can lower the required torque by 15–25%. Always confirm against the joint design, especially when going up a strength class.
Proof Load & Strength for M20
| Tensile stress area As (ISO 898-1) | 245 mm² |
|---|---|
| Proof load, class 8.8 | 147 kN |
| Proof load, class 10.9 | 203 kN |
| Proof load, class 12.9 | 238 kN |
| Min. ultimate tensile, class 8.8 | 196 kN |
Proof load = stress area × proof stress per ISO 898-1. Design joints so the working preload stays below the proof load of the selected class.
M20 Hex Socket Cone Point Set Screw — GB/T 78 / ISO 4027 (Series 027) Weight
A steel M20 hex socket cone point set screw at the listed 30 mm length weighs approximately 42 g each — about 42 kg per 1,000 pieces. Stainless A2/A4 weighs roughly the same (density 7.9–8.0 g/cm³). Actual weight varies slightly with head form, thread and finish; use this figure for freight estimation only.
Common Applications for M20 Hex Socket Cone Point Set Screw — GB/T 78 / ISO 4027 (Series 027)
M20 Hex Socket Cone Point Set Screw — GB/T 78 / ISO 4027 (Series 027) are commonly specified for heavy assembly and large machine mounts.
Installation Tips for M20 Hex Socket Cone Point Set Screw — GB/T 78 / ISO 4027 (Series 027)
- Use a quality Allen key fully seated in the socket — partial engagement is the most common cause of stripped sockets at this size.
- For countersunk and button-head variants, chamfer the through-hole to seat the head flush without preloading the head/shank fillet.
- At M20 the stretch in the bolt becomes the controlling factor — for critical joints, use angle-controlled or stretch-controlled tightening instead of pure torque.
When to Step Up or Down from M20
When the joint preload approaches the proof load of M20 class 8.8, step up to M24 class 8.8 (or move to M20 class 10.9). When the joint is over-specified, M16 often saves weight and cost without losing the safety margin.