Skip to content
info@engineeringhardware.com
Request a Quote

Rigging Hardware · ISO / DIN

DIN Wire Rope Clip (U-Bolt) — ISO / DIN (Series 157)

Wire Rope Clip (U-Bolt) — ISO / DIN (Series 157) manufactured to DIN follow a specific scope. This page summarizes that scope, lists every dimension the standard fixes, and points to the most common cross-references.

DIN — Scope

DIN specifies the dimensions and tolerances of wire rope clip (u-bolt) — iso / din (series 157). Material, property class, surface finish and packaging are governed by separate documents in the same standards family (for example ISO 898-1 for the mechanical property classes of bolts and screws).

Tolerance & Product Grades

DIN, alongside the related ISO / DIN entries on this site, specifies product grades (typically A or B for fine work and C for general engineering) and tolerance classes for the controlling dimensions. Choose the grade against the precision your application requires.

Dimensions Specified by DIN

For rope diameter (mm)U-bolt diameter (mm)Saddle width (mm)Bolt threadWorking load limit (kg)Reference standard
6M516M560DIN 1142 / GB/T 5976
8M620M6110DIN 1142 / GB/T 5976
10M826M8180DIN 1142 / GB/T 5976
12M1032M10260DIN 1142 / GB/T 5976
16M1238M12460DIN 1142 / GB/T 5976
20M1445M14720DIN 1142 / GB/T 5976
24M1655M161050DIN 1142 / GB/T 5976
30M2070M201640DIN 1142 / GB/T 5976

Equivalent Standards

Where direct equivalents exist (ISO ↔ DIN, ISO ↔ ASME), they are listed on the parent Wire Rope Clip (U-Bolt) — ISO / DIN (Series 157) page. Always confirm against the dimensions on this page, since some "equivalent" standards differ in tolerances and head geometry.

Companion Standards

DIN controls only the geometry of wire rope clip (u-bolt) — iso / din (series 157). The mechanical strength is set by ISO 898-1 (bolts and screws) or ISO 898-2 (nuts); the surface finish is governed by separate finish standards (e.g. ISO 4042 for electroplating). For corrosion testing, the relevant document is ISO 9227 (neutral salt spray).

Technical Drawing

Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.

Sends the selected values to the quote form below.

Request a Quote

Adjust the parameters in the drawing above and click "Request this configuration" to send the exact specification straight to this form.

Request a Quotation

Specification
Business Information

Dimensions & Specifications (ISO / DIN)

For rope diameter (mm)U-bolt diameter (mm)Saddle width (mm)Bolt threadWorking load limit (kg)Reference standard
6M516M560DIN 1142 / GB/T 5976
8M620M6110DIN 1142 / GB/T 5976
10M826M8180DIN 1142 / GB/T 5976
12M1032M10260DIN 1142 / GB/T 5976
16M1238M12460DIN 1142 / GB/T 5976
20M1445M14720DIN 1142 / GB/T 5976
24M1655M161050DIN 1142 / GB/T 5976
30M2070M201640DIN 1142 / GB/T 5976

Frequently Asked Questions

Does DIN specify the mechanical strength?

No. DIN controls only the geometry of wire rope clip (u-bolt) — iso / din (series 157). The mechanical strength is set by ISO 898-1 (bolts / screws) or ISO 898-2 (nuts), and the finish is governed by separate standards.

Can I substitute DIN for the corresponding DIN standard on a drawing?

On modern drawings the ISO standard is the master reference; the older DIN equivalent is a cross-reference. For most dimensional purposes the parts are interchangeable, but check tolerance grades and the head height — these are the most common points of divergence.

When did DIN last revise its dimensional table?

ISO standards for wire rope clip (u-bolt) — iso / din (series 157) are reviewed on roughly a five-year cycle. Always reference the latest published edition (or the edition cited contractually); the dimensional table on this page reflects the current commercially-supplied form.

What does DIN specify for Wire Rope Clip (U-Bolt) — ISO / DIN (Series 157)?

DIN specifies the dimensions and tolerances of wire rope clip (u-bolt) — iso / din (series 157). Material and property class are governed by separate standards in the same family.

How do I request a quotation?

Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.