GB/T 70.3 specifies the dimensions and tolerances for drilled-head capstan sealing screws. The full dimensional table is reproduced below, followed by the DIN, ISO and ASME parts that match or supersede it.
- Standard
- GB/T 70.3
- Product
- Drilled-Head Capstan Sealing Screws
- Governing standards
- GB/T 70.1 / DIN 912 / ISO 4762 and GB/T 70.3 / DIN 7991 / ISO 10642
Equivalence between national standards is dimensional, not always metallurgical. Check the property class separately when substituting.
The table below lists the dimensions catalogued for drilled-head capstan sealing screws under GB/T 70.3. The scope of GB/T 70.3 itself is not summarised here — where a figure matters, confirm it against the published document.
GB/T 70.3 — Scope
The table below lists the dimensions catalogued for drilled-head capstan sealing screws under GB/T 70.3. The scope of GB/T 70.3 itself is not summarised here — where a figure matters, confirm it against the published document.
Tolerance & Product Grades
Product grade is a concept from dimensional fastener standards and does not apply to GB/T 70.3. Tolerances for this part are the limits shown against each dimension in the table.
Dimensions Specified by GB/T 70.3
| Head form | Governing standards | Sealing feature | Property class | Finish |
|---|
| hexagon socket head cap | GB/T 70.1-2008 / DIN 912 / ISO 4762 | cross-drilled head for sealing wire | 8.8 | black oxide |
| countersunk hexagon socket | GB/T 70.3-2008 / DIN 7991 / ISO 10642 | cross-drilled head for sealing wire | 8.8 | black oxide |
Equivalent Standards
Where direct equivalents exist (ISO ↔ DIN, ISO ↔ ASME), they are listed on the parent Drilled-Head Capstan Sealing Screws page.
Always confirm against the dimensions on this page, since some "equivalent" standards differ in tolerances and head geometry.
When to Specify GB/T 70.3
Choose GB/T 70.3 for international engineering work and OEM supply where ISO standards are the contractual reference. It is the default modern specification for drilled-head capstan sealing screws.
Custom manufacturing · Made to drawing
Need a screw to this standard in a non-standard size?
Parts built to GB T 70 3 are already in the catalog, so a special is usually a variation on existing tooling rather than a new design — which is what keeps the cost down. Made by cold heading or warm forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
Custom screw manufacturingSend a drawing
Applications & Industries
Drilled-Head Capstan Sealing Screws are bought for a small number of well-defined jobs. These are the ones we ship them for. Stocked from hexagon socket head cap to countersunk hexagon socket (nominal diameter).
Industries that specify Drilled-Head Capstan Sealing Screws
-
Regulated installations
Evidence of an unbroken seal on inspection.
-
Utility metering
A cross-drilled head takes a sealing wire that shows tampering.
-
Instrument enclosures
Closure control on calibrated equipment.
-
Test and measurement
Sealed access for certified instruments.
-
Food, pharma & cleanroom
Stainless assemblies that are washed down, where the finish matters as much as the strength.
-
Machine building & OEM
The default fastener on production equipment: covers, brackets, motor mounts and sub-assemblies tightened to a specified torque.
Typical applications
- recording the seal number against the installation
- threading a sealing wire through the drilled head and crimping it
- choosing the cap or countersunk form for the enclosure detail
- specifying class 8.8 black oxide as listed
- joints where the property class is stated on the drawing
- clamping two machined faces to a calculated preload
Service conditions to specify against
- Marine and coastal
- Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
- High load
- Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
- Sealed joints
- Used where the fixing has to keep water or air out as well as hold — the elastomer, not the fastener, decides service life.
- Torque and preload
- The joint is designed around bolt tension, so lubrication, coating and the friction coefficient all change the torque figure — state them together.
Where to use something else
- Do not fit a sealing screw without actually closing the wire; an undrawn seal proves nothing.
- Do not use a machine thread into unthreaded sheet or timber; use a tapping screw, rivet nut or insert made for that parent material.
Full application guide: where Drilled-Head Capstan Sealing Screws are used, how to specify them, and the cases they are wrong for