GB/T 93 is the standard cited for spring lock washer (gb/t 93). This page sets out what the standard controls for this part, reproduces the dimensional table supplied against it, and notes the related designations referenced on drawings.
GB/T 93 — Scope
GB/T 93 is "Spring lock washers". GB/T 93 is the Chinese national adoption of the same document.
Tolerance & Product Grades
GB/T 93 does not divide spring lock washer (gb/t 93) — gb/t 93 / din 127b (series 081) into product grades. Tolerances are given as limits on the individual dimensions in the table.
Where a general-tolerance class is cited on the drawing instead, it applies to the dimensions not otherwise toleranced.
Dimensions Specified by GB/T 93
| For bolt size | Inner diameter d1 (mm) | Outer diameter d2 (mm) | Width b (mm) | Thickness t (mm) | Reference standard |
|---|---|---|---|---|---|
| M3 | 3.1 | 6.2 | 1.0 | 0.8 | GB/T 93 / DIN 127B |
| M4 | 4.1 | 7.6 | 1.2 | 1.0 | GB/T 93 / DIN 127B |
| M5 | 5.1 | 9.2 | 1.5 | 1.2 | GB/T 93 / DIN 127B |
| M6 | 6.1 | 11.8 | 2.0 | 1.6 | GB/T 93 / DIN 127B |
| M8 | 8.1 | 14.8 | 2.5 | 2.0 | GB/T 93 / DIN 127B |
| M10 | 10.2 | 18.1 | 3.0 | 2.5 | GB/T 93 / DIN 127B |
| M12 | 12.2 | 21.1 | 3.5 | 3.0 | GB/T 93 / DIN 127B |
| M14 | 14.2 | 24.1 | 4.0 | 3.5 | GB/T 93 / DIN 127B |
| M16 | 16.2 | 27.4 | 4.5 | 4.0 | GB/T 93 / DIN 127B |
| M18 | 18.2 | 29.4 | 5.0 | 4.5 | GB/T 93 / DIN 127B |
| M20 | 20.2 | 33.6 | 5.5 | 5.0 | GB/T 93 / DIN 127B |
| M24 | 24.5 | 40.1 | 6.5 | 6.0 | GB/T 93 / DIN 127B |
| M30 | 30.5 | 50.0 | 8.0 | 7.5 | GB/T 93 / DIN 127B |
Companion Standards
GB/T 93 controls the geometry of spring lock washer (gb/t 93) — gb/t 93 / din 127b (series 081). Surface finish is governed by separate finish standards such as ISO 4042 for electroplating, and corrosion testing by ISO 9227 (neutral salt spray). Mechanical performance is set by the documents specific to this part family — ISO 898-1 and ISO 898-2 apply to bolts, screws, studs and nuts, and not here.
When to Specify GB/T 93
Choose GB/T 93 for international engineering work and OEM supply where ISO standards are the contractual reference. It is the default modern specification for spring lock washer (gb/t 93) — gb/t 93 / din 127b (series 081).
Custom manufacturing · Made to drawing
Need a washer to this standard in a non-standard size?
Parts built to GB T 93 are already in the catalog, so a special is usually a variation on existing tooling rather than a new design — which is what keeps the cost down. Made by stamping or punching.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
