For studs & threaded rods, DIN 975 fixes the geometry and the tolerances. The sections below describe the scope of the document, the properties it deliberately leaves to companion standards, and the equivalent designations across standards bodies.
DIN 975 — Scope
DIN 975 is "Threaded rods".
Material, property class, surface finish and packaging are governed by separate documents — ISO 898-1 and ISO 898-2 for mechanical property classes, ISO 4042 for electroplated finishes.
Tolerance & Product Grades
DIN 975 does not divide studs & threaded rods into product grades. Tolerances are given as limits on the individual dimensions in the table.
Where a general-tolerance class is cited on the drawing instead, it applies to the dimensions not otherwise toleranced.
Dimensions Specified by DIN 975
| Thread size | Pitch (mm) | Point type | Common lengths (mm) | Reference standard | Notes |
|---|---|---|---|---|---|
| M4 | 0.7 | M4 | 10~100 | DIN 939 | Stud, equal thread both ends |
| M5 | 0.8 | M5 | 10~120 | DIN 939 | Stud, equal thread both ends |
| M6 | 1.0 | M6 | 12~160 | DIN 939 | Stud, equal thread both ends |
| M8 | 1.25 | M8 | 16~200 | DIN 939 | Stud, equal thread both ends |
| M10 | 1.5 | M10 | 20~250 | DIN 939 | Stud, equal thread both ends |
| M12 | 1.75 | M12 | 25~300 | DIN 939 | Stud, equal thread both ends |
| M14 | 2.0 | M14 | 30~300 | DIN 939 | Stud, equal thread both ends |
| M16 | 2.0 | M16 | 35~300 | DIN 939 | Stud, equal thread both ends |
| M18 | 2.5 | M18 | 40~300 | DIN 939 | Stud, equal thread both ends |
| M20 | 2.5 | M20 | 45~300 | DIN 939 | Stud, equal thread both ends |
| M22 | 2.5 | M22 | 50~300 | DIN 939 | Stud, equal thread both ends |
| M24 | 3.0 | M24 | 50~300 | DIN 939 | Stud, equal thread both ends |
| M27 | 3.0 | M27 | 55~300 | DIN 939 | Stud, equal thread both ends |
| M30 | 3.5 | M30 | 60~300 | DIN 939 | Stud, equal thread both ends |
| M36 | 4.0 | M36 | 70~300 | DIN 939 | Stud, equal thread both ends |
| M42 | 4.5 | M42 | 80~300 | DIN 940 | Stud, equal thread both ends |
| M48 | 5.0 | M48 | 90~300 | DIN 940 | Stud, equal thread both ends |
| M4 | 0.7 | Fully threaded | 1000/2000/3000 | DIN 975 | Fully threaded rod, cut to length |
| M5 | 0.8 | Fully threaded | 1000/2000/3000 | DIN 975 | Fully threaded rod, cut to length |
| M6 | 1.0 | Fully threaded | 1000/2000/3000 | DIN 975 | Fully threaded rod, cut to length |
| M8 | 1.25 | Fully threaded | 1000/2000/3000 | DIN 975 | Fully threaded rod, cut to length |
| M10 | 1.5 | Fully threaded | 1000/2000/3000 | DIN 975 | Fully threaded rod, cut to length |
| M12 | 1.75 | Fully threaded | 1000/2000/3000 | DIN 975 | Fully threaded rod, cut to length |
| M16 | 2.0 | Fully threaded | 1000/2000/3000 | DIN 975 | Fully threaded rod, cut to length |
| M20 | 2.5 | Fully threaded | 1000/2000/3000 | DIN 975 | Fully threaded rod, cut to length |
| M24 | 3.0 | Fully threaded | 1000/2000/3000 | DIN 975 | Fully threaded rod, cut to length |
| M30 | 3.5 | Fully threaded | 1000/2000/3000 | DIN 975 | Fully threaded rod, cut to length |
Equivalent Standards
Where direct equivalents exist (ISO ↔ DIN, ISO ↔ ASME), they are listed on the parent Studs & Threaded Rods page.
Always confirm against the dimensions on this page, since some "equivalent" standards differ in tolerances and head geometry.
When to Specify DIN 975
DIN 975 is still widely used in European mechanical engineering and as a cross-reference on legacy drawings; its ISO equivalent is preferred for new designs.
Custom manufacturing · Made to drawing
Need a bolt to this standard in a non-standard size?
Parts built to DIN 975 are already in the catalog, so a special is usually a variation on existing tooling rather than a new design — which is what keeps the cost down. Made by cold heading or hot forging.
Minimum order from 2,000 pieces; samples within 7 days of drawing approval.
